26. In which of the following applications D.C. series motor is invariably tried?
(a) Starter for a car
(b) Drive for a water pump
(c) Fan motor
(d) Motor operation in A.C. or D.C.
Ans: a
27. In D.C. machines fractional pitch winding is used
(a) to improve cooling
(b) to reduce copper losses
(c) to increase the generated e.m.f.
(d) to reduce the sparking
Ans: d
28. A three point starter is considered suitable for
(a) shunt motors
(b) shunt as well as compound motors
(c) shunt, compound and series motors
(d) all D.C. motors
Ans: b
29. In case-the conditions for maximum power for a D.C. motor are established, the efficiency of the motor will be
(a) 100%
(b) around 90%
(c) anywhere between 75% and 90%
(d) less than 50%
Ans: d
30. The ratio of starting torque to full-load torque is least in case of
(a) series motors
(b) shunt motors
(c) compound motors
(d) none of the above
Ans: b
32. In D.C. motor which of the following can sustain the maximum temperature rise?
(a) Slip rings
(b) Commutator
(c) Field winding
(d) Armature winding
Ans: c
33. Which of the following law/rule can he used to determine the direction of rotation of D.C. motor ?
(a) Lenz’s law
(b) Faraday’s law
(c) Coloumb’s law
(d) Fleming’s left-hand rule
Ans: d
34. Which of the following load normally needs starting torque more than the rated torque?
(a) Blowers
(b) Conveyors
(c) Air compressors
(d) Centrifugal pumps
Ans: b
35. The starting resistance of a D.C. motor is generally
(a) low
(b) around 500 Q
(c) 1000 Q
(d) infinitely large
Ans: a
36. The speed of a D.C. series motor is
(a) proportional to the armature current
(b) proportional to the square of the armature current
(c) proportional to field current
(d) inversely proportional to the armature current
Ans: d
37. In a D.C. series motor, if the armature current is reduced by 50%, the torque of the motor will be equal to
(a) 100% of the previous value
(b) 50% of the previous value
(c) 25% of the previous value
(d) 10% of the previous value
(e) none of the above
Ans: c
38. The current drawn by the armature of D.C. motor is directly proportional to
(a) the torque required
(b) the speed of the motor
(c) the voltage across the terminals
(d) none of the above
Ans: a
39. The power mentioned on the name plate of an electric motor indicates
(a) the power drawn in kW
(b) the power drawn in kVA
(c) the gross power
(d) the output power available at the shaft
Ans: d
40. Which D.C. motor has got maximum self loading property?
(a) Series motor
(b) Shunt motor
(c) Cumulatively compounded ‘motor
(d) Differentially compounded motor
Ans: d
41. Which D.C. motor will be suitable along with flywheel for intermittent light and heavy loads?
(a) Series motor
(b) Shunt motor
(c) Cumulatively compounded motor
(d) Differentially compounded motor
Ans: c
42. If a D.C. shunt motor is working at no load and if shunt field circuit suddenly opens
(a) nothing will happen to th£ motor
(b) this will make armature to take heavy current, possibly burning it
(c) this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses
(d) motor will run at very slow speed
Ans: c
43. D.C. series motors are used
(a) where load is constant
(b) where load changes frequently
(c) where constant operating speed is needed
(d) in none of the above situations.
Ans: d
44. For the same H.P. rating and full load speed, following motor has poor starting torque
(a) shunt
(b) series
(c) differentially compounded
(d) cumulativelyc’ompounded
Ans: c
45. In case of conductively compensated D.C. series motors, the compensating winding is provided
(a) as separately wound unit
(6) in parallel with armature winding
(c) in series with armature winding
(d) in parallel with field winding
Ans: c
46. Sparking at the commutator of a D.C. motor may result in
(a) damage to commutator segments
(b) damage to commutator insulation
(c) increased power consumption
(d) all of the above
Ans: d
47. Which of the following motor is preferred for operation in highly explosive atmosphere ?
(a) Series motor
(b) Shunt motor
(c) Air motor
(d) Battery operated motor
Ans: c
48. If the supply voltage for a D.C. motor is increased, which of the following will decrease ?
(a) Starting torque
(b) Operating speed
(c) Full-load current
(d) All of the above
Ans: c
49. Which one of the following is not the function of pole shoes in a D.C. machine ?
(a) To reduce eddy current loss
(b) To support the field coils
(c) To spread out flux for better unifor-mity
(d) To reduce the reluctance of the magnetic path
Ans: a
50. The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is
(a) 4.0
(b) 2.0
(c) 1.0
(d) 0.5
Ans: d